3+ years experience in electrical field in Oil and Gas (Onshore & Offshore) and EPC (Hydropower) company. Having relevant experience in maintenance, engineering, project development, and contract. Currently developing knowledge in steady state analysis such as Load Flow Analysis, Short Circuit Analysis, Motor Starting, Transient Stability, Protection Coordination, Arc Flash Studies and Harmonic Analysis using ETAP and DIgSILENT PowerFactory. Also for transient analysis in Insulation Coordination such as Temporary Overvoltage (TOV), Switching Front Overvoltage (SFO), Fast Front Overvoltage (FFO), Transient Recovery Voltage, Very Fast Transient Overvoltage (VFTO) using PSCAD/EMTDC. Familiar both national and international standards such as SPLN, IEC, NEMA, NEC, IEEE, ANSI and NFPA

Engineer

More than 12 years’ experience in EPC for Oil & Gas, Manufacturing Heavy Equipment, and Power Plant Construction. Proven ability in Quality Assurance, Quality Control, and interface. Hands-on experience with CSWIP 3.2.1, CSWIP 3.1, and CSWIP 3.0, with additional certifications including ASNT Level II NDT and Qualified Painting Inspector. I hold a Bachelor of Mechanical Engineering degree. Having experience undertaken Projects covering a wide range of Oil & Gas Topside Fabrication project for Wellhead & Riser Platforms, Accommodation & Process Platforms, Pipe Rack foundations, Substation Modules, FPSO modules, Heavy Equipment and Onshore Power Plant Construction.

Inspector, Supervisor / Technician, Other

Electrical engineer with more than 12+ years of experience at Oil & Gas sector. Familiar with PTS, IEC, EX requirement on electrical package. Experience with Detail Design Engineering, Electrical inspection, Construction, Pre-commissioning & Commissioning. Has involve in EPCC, PCC, Brownfield, and Greenfield & Hook-up Commissioning.

Engineer

I graduated from the IUCTT, Sri Damansara in 2011 with a Bachelor engineering in Electronic and Instrumentation Engineering and Master in Industrial Engineering from Universiti Malaysia Pahang. I started my carrier as a Technical Executive specializing in condition monitoring (vibration and thermography inspection) at AF Condition Monitoring Sdn Bhd (2009-2010) and as a Site Engineer at Tanjung CSI Sdn Bhd (Tanjung Offshore Group, 2011). Currently I'm working with EPCC company, Tanjung Offshore Services Sdn.Bhd (subsidiary of T7 Global Berhad) as a Senior Construction Project Engineer for multi disciplinary projects. My previous job combining with electrical, instrumentation, mechanical, machine maintenance, structure, piping fabrication and construction, inspection which specialize in project management & hook-up installation. I have seen the wonderful creations of your company and was startled by the precision, accuracy and elegance of your work. I aspire to learn to produce designs of such a high quality.

Engineer, Superintendent, Manager, Inspector

Hi, welcome and thank you for checking out my profile! I am currently working as a Freelance Mechanical engineer in fields of : design, computational mechanics, programming (/automating) and project management. I completed my Mechanical & Design Engineering studies with a Master in Business & Management. I am looking for missions to make a big impact in a company/research group taking on new and exciting challenges. Competencies : Automating | Finite Element Analysis / Method | CAE | CAD | 3D Design | Project Management | Continuous Improvment | Research & Development | Process | Method Design & Simulation softwares : SolidWorks | Catia | Oneshape | Ansys | Abaqus Programming languages : VBA | MATLAB | Python Other softwares : Power BI | Microsoft Excel | SAP | Pack Office Let's work together !

Engineer, Supervisor / Technician, Manager, Other, Superintendent, Inspector, Drafter / Designer

Adaptable and innovative qualified Mechanical Engineer with over 15 years of experience in the power generation sector. My experience includes working within maintenance, installation, and commissioning power stations, especially gas and steam turbines in the most best-selling brands in different capacities such as; GE, Alstom , Siemens, Mitsubishi and Ansaldo Energia. I have ability to analyze engineering problems, evaluate and recommend alternative solutions and communicate recommendations effectively with strengths include ability to work in multinational environment, good problem solving, hands on team player, able to work at all levels and under pressure, self motivated, energetic with leading management and strong communications skills. I have always been intrigued by and cherished the idea of working in a competitive environment and been seeking an opportunity to express my potentials.

Engineer

Chemical Engineer with 11+ years' experience in oil and gas industry and petrochemical plants through proven experience knowledge in multiple gas processing including acid gas removal (amine sweetening), gas dehydration (liquid/solid) desiccants, NGL Recovery and LNG Technology. Solid experience in process simulation software Aspen HYSYS. Solid information and experience in process safety studies, such as PHA Analysis, HAZID, HAZOP, Bow-tie, SIMOPS, SIL Assessment, Consequence Modeling, FERA, QRA and ALARP. Strong leadership, communication skills, and proactive attitude to ensure effective integration between different multi-cultural multi-discipline teams.

Engineer

SUMMARY I am a Subsea Engineer with twelve years' work experience. Currently working as freelance consultant Project Engineer for onshore and offshore project. I previously worked as a senior subsea engineer at WorleyParsons on the HESS Deep Water Tano Ghana Project on riser/pipeline, subsea controls/ hardware & Flow Assurance SURF FEED design and also as Subsea Field Engineer at WorleyParsons Atlantic with TechnipFMC on Tullow oil's Tweneboa, Ntomme, and Enyinra (TEN) and Jubilee oil fields project in Ghana and Technip FMC Bonga project in Nigeria for two years. At TechnipFMC, I was responsible for performing Site Receival Test, mobilization and demobilization subsea operations, SIT (System Integration Test), FAT (Factory Acceptance Test), Load Out, EFAT (Extended Factory Acceptance Test) and mandatory/periodic maintenance/installation operations on subsea equipment including tubing hanger, Christmas tree, Manifolds, Riser Base, PLET, SCM, ROV tools and other subsea equipment, running tools. Provided support for offshore completions of well and part of the TEN oil and gas field Subsea Umbilical Riser Flowline (SURF) and Installation Hook-Up and Commissioning (IHUC) commissioning team for topside and subsea structure on Tullow TEN FPSO in Singapore. Also involved in the TEN field operational field start-up, pre commissioning activities, installation of flowlines, in-line umbilicals, Hydraulic Flying Leads, EFLs, flexible pipelines and subsea structures in Ghana. Gained expert knowledge in subsea engineering (MSc) from the University of Aberdeen, Scotland which entails the use of CAE/FEA Software for various designs relating to subsea production systems, pipelines design, installation and soil mechanic, Subsea Construction, Inspection and Maintenance, Subsea Equipment Integrity, Safety and Reliability Engineering, Risers and Hydrodynamics and Subsea controls and currently working toward attaining chartered engineering status and a member of the Project Management Institute (PMI). Four and half years' experience in the Mining industry, mainly working as operational maintenance superintendent, senior maintenance supervisor and maintenance planner with an Australian mining contracting company called African Mining Services (AMS) and was responsible for operations and maintaining mobile heavy-duty mining equipment.

Engineer, Superintendent, Supervisor / Technician, Manager

Asset Integrity Management EMAS Asset Integrity Management ·       Developed a comprehensive Asset Register for all tagged equipment, including electrical, rotating, static, civil, and instrumentation assets. ·       Prepared a detailed Bill of Materials (BOM) for all tagged equipment to support maintenance planning and inventory management. ·       Established a structured Maintenance Plan (MPlan) for rotating, static, electrical equipment, and instrument. ·       Developed Failure Modes and Effects Analysis (FMEA) to identify potential failure points and improve equipment reliability. ·       Created an Equipment Reliability Strategy (ERS) to optimize maintenance schedules and minimize equipment downtime. Gas Lift Compressor (GLC) – J4DP-A Wells ·       Performed a comprehensive RAM analysis of the GLC process system using MAROS Software, optimizing system efficiency and uptime. ·       Developed a complete BOM for the GLC process system based on the Piping & Instrumentation Diagram (P&ID) provided by the vendor. FEED NC8 GFD Project ·       Conducted a detailed RAM study inclusive of Basis of Study and RAM report for the NC8 Wellhead Platform (WHP) using MAROS Software. ·       Developed a CR report and TOR for CR workshop inclusive of the following nodes: o Installation of riser from NC8-WHP o Installation of new pipeline within the field o Installation of Jackets and Topsides of NC8-WHP o Installation of HTI at NC3-WHP o Installation of subsea cable FEED – Baram Junior Cluster ·       Conducted an Safety Critical Element-Performance Standard (SCEPS) study for HTI at BNCPP-B platform. BED – Baram Junior Cluster ·       Conducted an SCEPS study for HTI at BNCPP-B platform. DED – Baram Junior Cluster ·       Conducted an SCEPS study for HTI at BNCPP-B platform. The SCEPS is updated based on the newly provided P&ID, EESA report, Fire Fighting Layout, etc.   Corrosion Design & Material Selection EPCC Kerteh Rejuvenation Project (KREJUV) ·       Conducted a Corrosion Design Basis Memorandum (CDBM) for an onshore pipeline for KREJUV and utilized ECE 5.8 and ASPEN Hysys for process and SLC calculation. BED for Industrial Effluent Treatment System (IETS) Upgrading Project at GPK ·       Conducted a CDBM for non-metallic piping and tanks within the system. FEED – Baram Junior Cluster ·       Conducted Material Selection Studies for topside piping, utility piping, and pipelines at Fatimah Drilling Platform-A (FTDP-A), Salbiah Drilling Platform-A (SLDP-A), and Baronia Central Processing Plant-B (BNCCP-B) using ECE 5.8 to assess corrosion rates for a 10-year operation period, supported by process data from ASPEN HYSYS. BED Quadruple Project Phase 2 ·       Conducted the CDBM and Material Selection Study as part of the Basic Engineering Design, including comprehensive simulations, calculations, and technical evaluations. DED – Baram Junior Cluster ·       Conducted Material Selection Studies for topside piping, utility piping, and pipelines at SLDP-A and BNCPP-B using ECE 5.8 to assess corrosion rates for a 10-year operation period, supported by process data from ASPEN HYSYS. ·       Conducted CDBM Studies for topside piping, utility piping, and pipelines at SLDP-A and BNCPP-B using ECE 5.8 to assess corrosion rates for a 10-year operation period.   Safety & Constructability Review Studies Drop Object Protection – KND Platform ·       Developed HAZID and Constructability Review (CR) reports for Drop Object Protection Study. FEED – Baram Junior Cluster ·       Scriber for HAZOP and HAZID studies for BNCPP-B and SALBIAH & FATIMAH Drilling Platforms. DED for BEKOK-AA New Gas Injection Flowlines ·       Developed HAZOP, HAZID, and Thermal Radiation & Gas Dispersion Studies to ensure safe and efficient flowline design and operation. DED – Baram Junior Cluster ·       Conducted Bow-Tie study for SLDP-A based on existing HSE Case for BNCPP-B and HER report developed. Firewater System Analysis for PM3S Bunga Raya Complex ·       Developed an Assumption Register for Firewater Demand and Hydraulic Calculations. ·       Prepared the Firewater Demand Calculation Report. DED – Baram Junior Cluster ·       Conducted an Bow-Tie study for HTI at SLDP-A WHP (Greenfield). EPCC Kerteh Rejuvenation Project (KREJUV) ·       Developed Firefighting, Lifesaving, and Safety Equipment Datasheet and Specification.   Front-End Engineering Design, Feasibility Study, & Project Management Feasibility Study for PILOT Project (Current) Project Planning & Coordination: ·       Conducted Pre-Project Kick-Off Meeting activities, including: ·       Defining the Scope of Work ·       Establishing the Project Schedule ·       Developing the Master Deliverables Register ·       Developed a Cost Estimation Report based on AACE Class 5 standards to establish preliminary project budgeting. ·       Created a Technical Assurance Plan for the FEED Phase to ensure compliance with industry standards, technical integrity, and project quality. Technical Design: ·       Performed Steady-State Flow Assurance Analysis using PIPESIM. ·       Developed the Subsea Production System Report detailing subsea configurations and system integrity. ·       Created the Design Basis for Process, outlining key process parameters and design considerations. ·       Formulated the Overall Field Development Scheme to optimize production and operational efficiency. ·       Developed the Brownfield Modification Report for integration with existing facilities. ·       Engineering Studies & Reporting: ·       Prepared the Risk and Opportunity Report to identify potential project challenges and mitigation strategies. ·       Conducted a Concept Screening Assessment to evaluate viable development options. ·       Compiled the comprehensive Final Feasibility Report, consolidating all technical, commercial, and risk assessments. ·       Developed a Cost Estimation Report based on AACE Class 5 standards to establish preliminary project budgeting.   Feasibility Study for FB-1 Market & Commercial Analysis: ·       Conducted a Market Survey Research to evaluate potential vendors, technologies, and cost implications. ·       Developed a comprehensive Procurement and Contracting Strategy to streamline project execution and optimize costs. ·       Developed a Cost Estimation Report based on AACE Class 5 standards to establish preliminary project budgeting. ·       Created a Technical Assurance Plan for the FEED Phase to ensure compliance with industry standards, technical integrity, and project quality. Risk Management: ·       Prepared a detailed Risk and Opportunity Assessment to identify potential challenges and strategic opportunities throughout the project lifecycle. ·       Process Safety & Design Evaluation: ·       HAZID (Hazard Identification) Study featuring twelve (12) nodes, evaluating: ·       Two tie-in options: MPPL or Existing WHP ·       Comparative assessment between Wellhead Platform (WHP) and Subsea Production System (SPS) configurations. Pipeline Engineering & Integrity Assessments for PL354 & PL359 ·       Executed detailed pipeline integrity assessments and provided technical solutions to enhance operational reliability and safety. HSE & Fire Protection Philosophy Development for BioMEG Commercial Plant ·       Led the development of the HSE and Fire Protection Philosophy, ensuring alignment with industry best practices and regulatory requirements.   BED Dam Doi and Khanh My WHP and Pipeline Installation and Modification ·       Developed Value Engineering (VE) reports for DD-WHP, KM-WHP, and HTI at BK-C WHP. ·       Developed CR reports for the following nodes: o Installation and modification of new extension deck at BK-C WHP o Installation of riser at BK-C WHP o Installation of Jackets and Topsides for DD-WHP and KM-WHP o Installation of new pipelines Advanced Diagnostics & Predictive Modelling: ·       Designed models using iCON (Symmetry) by SLB for rotating equipment, including pumps, compressors, gas turbines, and steam turbines. ·       Utilized live input variables from OPUs to assess equipment health, collaborating closely with Group Digital and Process Engineers. Fault Diagnostics & Reliability Analysis: ·       Developed Failure Mode and Effects Analysis (FMEA) for extruders and Hydraulic Power Recovery Turbine (HPRT) based on ISO 14224 and Equipment Reliability Study (ERS) data. System Integration & Monitoring: ·       Deployed MRCSB and PGB trains into PRiSM Client, integrating alarms, P&ID diagrams, and DCS snapshots for continuous monitoring. Asset Life & Extension Studies: ·       Conducted an Asset Life Study (ALS) for 18 rotating equipment units at Subang Airport in collaboration with PETRONAS Dagangan Berhad (PDB), providing recommendations for future maintenance and operational strategies. ·       Performed an Asset Life Extension Study (ALES) for rotating equipment Kasawari CCS M1, assessing long-term asset viability. Rotating Equipment Design: ·       Operational optimization in the design evaluation of the E11 Fac and E11 Fac Phase 1 projects, contributing to the extension of the MLNG gas production plateau by an additional 1.5 years, with a focus on booster condensate pumps and compressors. ·       Conducted fire incident case studies involving rotating equipment at PETRONAS plants, identifying detectable symptoms and key monitoring parameters for future incident prevention. Renewable Energy: ·       Designed and modelled a biomass-based Combined Heat & Power (CHP) unit for commercial buildings, demonstrating cost-effective carbon reduction through HomerPro feasibility analysis ·       Engineered a 6.5 MW Horizontal Axial Wind Turbine blade design using Qblade software, optimizing for maximum power generation efficiency ·       Led design team for utility-scale Wind and Solar Hybrid Renewable Energy System, incorporating Sustainable Development Goals (SDGs) and achieving 85% renewable energy penetration ·       Performed detailed site analysis for wind farm implementations using WindPro, optimizing turbine placement for maximum energy yield ·       Design and installation of Grid-Connected Photovoltaic (GCPV) systems for residential and commercial applications. ·       Comprehensive site assessments, including shading analysis and load profiling, to optimize system design and layout. ·       Selection of photovoltaic (PV) modules and inverters, ensuring design efficiency and cost-effectiveness. ·       Performed single-phase electrical wiring and system integration in compliance with safety and regulatory standards. ·       Installation and assembly of PV system components, including mounting structures, modules, inverters, and protective devices. ·       System testing, commissioning, and performance verification to ensure operational readiness. ·       Maintenance support and troubleshooting for underperforming systems, implementing corrective actions to improve efficiency. ·       Full compliance with Malaysian Standards MS 1837:2018 and MS 2692:2020 throughout design and installation stages. ·       Certified SEDA Malaysia GCPV Systems Design, applying advanced skills in sizing, system layout, and regulatory alignment.

Engineer

1985 – 1997; Blue collar (onshore construction/heavy lift) 1998 – 2002; Full-time University student (working part-time) 2003 – present; White collar (marine engineering)

Engineer

Responsible for planning, executing, and leading pre-commissioning and commissioning activities for offshore and onshore oil & gas facilities, ensuring systems are completed, tested, and handed over safely in compliance with project specifications and international standards.

Superintendent, Supervisor / Technician, Engineer

• Construction experienced mechanical engineer. • Pre-Commissioning, Commissioning, Preservation, Mechanical completing, CCMS (Shell commissioning software in PDO Oman), check sheets, defining commissioning systems and sub systems, cost estimation, Velocity Air blowing, Lube Oil Flushing, Chemical Cleaning, Nitrogen / Helium Leak Testing, Flange management, Drying & Inserting of various Mechanical equipment and/or Piping. • Mechanical engineer with maintenance experience (static and rotation equipment). • Preparing detailed daily, weekly monthly and survey reports. • Piping Engineering, piping layout, hydro test, leaking test, Piping stress experienced. LPG experienced • Pipeline. • Refinery experienced mechanical engineer. Maintenance. • Crude oil tanks and tank farm maintenance activities. Site and office project engineering. Document management. Supervising of contractor teams on site. • Managing of "Department for preparation and manufacturing planning". Team leading of engineering group. Involving to maintenance activities. • Mechanical designing and computation of piping and mechanical devices (also springs included) in oil and gas industry and petrochemical industry • Mechanical designing of valves and fitting for industrial manufacturing according to ANSI, API, DIN, TEMA, NFPA, ISO and YUS Standards. During work to PDO Oman was in touch to Shell Design and Engineering Practices (DEPs). • CAD Design Engineering • As built activities and visually surveys

Senior Upstream Oil and Gas industry technical professional; over 25 years' experience providing solutions in demanding engineering, operations, and project management roles. Extensive global network. Key skills include: Comprehensive E&P Industry knowledge: Thorough understanding of the key fundamentals of the E&P industries' engineering disciplines. Proven ability to leverage these effectively to create business value and reduce HSSE risk. Project Management Exploration, Production Use basic and appropriate safety engineering practices, involve workforce in Process Safety, Improve safety culture, shared values in attitude and approach comes from leadership. Manage project delivery schedule, strictly implement project compliance to ensure project delivery complies with regulations. Responsible for project scope, schedule and cost, detailed planning and motitoring progress and delivery during the implementation phase. Operations Management: Expertise leading Field Development and Operational plans. Held line management project, production, maintenance & HSSE responsibility for complex offshore operation with annual CAPEX and OPEX budget. > $100M. Highly experienced and skilled in setting and managing budgets, operations and safety. FPSO's, subsea facilities and pipelines.

Engineer

An agile process instrument engineer with more than 3 years of experience in the oil & gas industry and driven to deliver excellence in the upstream energy sector. Specialized in design, sizing, and selection of new field instruments such as flowmeters, transmitters, sampling panels and gas analysers for Custody Transfer Metering Skids and Metering houses whilst upholding the industry standards and project specifications.

Engineer

To be part of a reputed firm and to work as a key player in challenging and creative environments that offers ample opportunities to add value to the firm and improve my personal skills, & To provide satisfactory services to Client.

Engineer, Manager

About ten (10) years working experience in ranged from Mechanical engineer, Construction Engineer, and Project Engineer who responsible in technical work such as design, calculation, work planning, project control, and engineering documentation. He also responsible to manage site work and delegate work among team from various department.

Engineer, Supervisor / Technician

Innovative and results-driven engineer. Skilled in process simulation and modelling, equipment sizing and selection, plant troubleshooting. Excellent communication skills, both verbal and written, with a strong focus on safety and environmental compliance. Seeking a challenging chemical engineering position at your company that will allow me to leverage my skills and experience to drive business success and growth.

Engineer

FIELD SERVICE TECHNICIAN with 20 years’ experience setting up and conducting testing and running of subsea equipment in workshop and offshore environments. Versed in Hydraulic control systems, IWOCs; hydro and gas pressure testing; mechanical assembly; fluid cleanliness. Highly flexible and capable in testing and assembly in both workshop and offshore environment. Focused on defining best practices and meeting quality standards and delivery deadlines. Extensive experience working with clients and implementing standard quality assurance processes. Thorough understanding of quality control inspections, examinations and testing. Focused on meeting deadlines and exceeding expectations. Motivated team player who works well in diverse team environment Willing to travel, flexible schedule and willingness to work long hours.

Supervisor / Technician, Inspector, Other

Multi-skilled project management professional with more than 22 years' progressive experience overseeing large-scale infrastructural project within Oil and Gas industry to schedule and budget. Possessing vast depth of Mechanical/Piping Engineering, Civil/Structural Engineering, Technical Construction/ Fabrication Management and Method, managerial, Project Management and Planning Scheduling experience on leading multi-disciplinary teams within multi-cultural environments. Familiar working with International Standard such as ASME, AWS, API, ASTM, ABS, BS/EN, JIS, AS/NZ, etc. Seeks a challenging and varied position that will enable me to capitalize on sound technical, Engineering, commercial and project management expertise, with opportunities for personal and professional growth.

Manager, Superintendent, Engineer

Results-driven Rotating Equipment Engineer with extensive experience managing complex projects in LNG plants, gas processing and transmission, and petrochemical complexes, refineries, FPSOs, and offshore platforms. Well-versed in leading diverse teams through conceptual, FEED, detailed design, construction, installation and commissioning phases as a PMC and EPC lead engineer whilst managing budgets and cost time resources.

Engineer, Inspector

Offshore/Subsea Structure/Installation Engineer with 12 years of experience in engineering, project management, and execution of oil and gas projects in both greenfield and brownfield areas. Project member of FEED, EPCI, and IMR Project (Contractor and Oil and Gas Operator/Client) which performing a feasibility study, detailed design, preparation work for construction, fabrication phase, construction, installation, and modification (repair and removal), monitoring project for offshore and subsea projects.

Engineer

I have developed a solid reputation for successfully and profitably managing numerous concurrent projects through all project phases from conception through completion within targeted cost, schedule, and compliance parameters. I feel confident that I can bring an excellent backdrop of professional experience that would serve well in this position. Some key points that are relevant to this opportunity include: • Successful management of multiple projects in the Gas and Oil industry from defining requirements through execution and closure, at various customer work sites in the US and abroad, including the activities of staff and subcontractors • Created applications that allocate resources and establish resource schedule, clarify completion criteria for each deliverable and develop acceptance plan • Acknowledged for outstanding performance by major oil company • A solid reputation as a hardworking, innovative and results-driven professional • Accreditations - PMI current member, PMP certification

Drafter / Designer, Engineer, Manager, Supervisor / Technician

I am an Electrical Engineering Specialist with more than 36 yoe in oil & gas, petrochemical, mining, power plant, renewable energies, and commercial buildings project fields. Has hands-on experiences on various positions on corporate & projects in EPC , Engineering Consultant companies such as Electrical Engineers, Lead/Senior Electrical Engineers, Principal Electrical & Instrumentation Engineer, Technical Advisor (TA)- Electrical, Head Of Department(HOD) Electrical Engineering, Deputy HOD Electrical Engineering, Subject Matter Electrical Expert, Project Engineering Manager, Engineering QAHSE Representative Coordinator, Business Development Coordinator.

Manager, Other, Superintendent

I am result-oriented professional who has been consistently praised as efficient by my co-workers and management over the period of my 11 years career, I’ve developed skill set directly relevant to the available role you are hiring for, including operations management, productivity and performance management and report generation.

Engineer, Inspector, Superintendent, Manager